Includes Zen Reef Nano Mag Magnetic Heater Mounts!
Over time any suction cup will start to fail, Zen Reef's Magnetic Heater Holders are the perfect solution. The BRS Titanium Heaters can slide into the circular cutouts that feature Zen Reef's Gridlox system to securely hold your heater but allow for easy removal and maintenance when necessary. The magnetic coupling system uses N52 grade neodymium magnets that are completely sealed on the wet & dry side, keeping the system 100% reef safe!
Keeping the temperature of your aquarium stable is one of the easiest things that can be done without having to invest in expensive electronics and fancy heat exchanging systems. The Bulk Reef Supply Titanium Aquarium Heater System is a complete temperature control system that includes a virtually unbreakable titanium heating element paired with a reliable and easy to use controller. The heater controller includes two large LCD displays that are easy to read and will let you know the current temperature of your aquarium along with the temperature programmed into the controller. Each heater controller can be custom calibrated and also features a replaceable temperature probe allowing the controller to last you a lifetime with simple probe maintenance. The heater(s) can plug into the 12" outlet dongle that is built into the controller and can control up to two heaters at the same time.
- 0.3°F Control Precision
- Precise Digital Readout
- Replaceable Temperature Probe
- Dual Heater Control
- Easy to Calibrate
- Adjustable Hysteresis
- Robust Titanium Heating Element
- Fully Submersible Elements
- Magnetic Mounting System
- 3-Year Heater Element Warranty
|Suggested Tank Size
|Power Cord Length
|0.83A @ 120VAC
|10.25" / 1"
|up to 40 Gallons
|1.6A @ 120VAC
|10.25" / 1"
|up to 75 Gallons
|2.5A @ 120VAC
|10.25" / 1"
|up to 100 Gallons
|5A @ 120VAC
|14.0" / 1"
|up to 200 Gallons
|10A @ 120VAC
|14.0" / 1" (each)
|up to 350 Gallons
Compared to glass heaters, titanium heaters are virtually unbreakable and will never shatter in your aquarium and can conduct heat through the body much quicker, ultimately making them more efficient. In most cases when a glass heater fails, the failure-prone seals will go bad allowing water into the heater body and can start to corrode the contents inside the heater causing water contamination and possible electric shock, or the body will just shatter leaving glass particles throughout your aquarium. Titanium heating elements take both of those risks and virtually eliminate them by having a shatterproof body along with welded end caps for a life-time of operation.
0.3°F Control Precision
Keeping a reef tank's temperature steady is crucial to long-term success and the BRS Heater Controller lets you set the temperature anywhere between 58°F and 99.9°F and then will keep it within 0.3°F of the controllers set temperature.
Replaceable Temperature Probe
The tank's temperature is sensed through a replaceable probe that is 72" long and only takes a few seconds if it ever needs to be replaced. The low-cost probe is perfect for conditions like saltwater aquariums, where deposits and algae can grow on the probe that requires vigorous cleaning, and ultimately being the main failure point. If you ever notice the temperature starts to drift or not hold a calibration it is usually a good sign that the probe needs to be replaced.
Control Range - 58°F - 99.9°F
Control Precision - 0.3°F up to 15°F (0.15°F - 7.5°F hysterisis)
Display Resolution - 0.1°F
Input Power - 120VAC @ 60Hz
Max Output Power - 10 amps @ 120VAC
Replaceable Temperature Probe Length - 72"
Outlet Dongle Length - 12"
Power Cord Length - 60"
Warranty - 1 Year
1x BRS Aquarium Heater Controller
1x BRS Titanium Aquarium Heater Element (1200w kit includes two heating elements)
1x Zen Reef Single Nano Mag Magnetic Heater Mount (1200w kit includes Dual Nano Mag Magnetic Mount)
1-Year Heater Controller Warranty
3-Year Heater Element Warranty
Hopefully I didn't miss this somewhere, but I noticed the instructions for the controller show a "Heat" light, but the unit I got matches the images here which say "Work1" and "Work2". What does that mean exactly? I assumed it would light when the respective outlet was on, but I also thought that both outlets were controlled simultaneously and it's never good to assume.
The second work2 light will not light up. It is meant for the other version of this controller that will do a chiller as well. Both heater plugs will follow the same programming.
We are expecting a shipment in at the end of the month, they will be available a day or so after that!
It can vary based on your home's temperature. That said, the 300w heater will be more than capable for your tank in most homes. Make sure to let us know if you have any other questions!