- PRO Series Anion DI Resin (Color Changing) - Part 2 - Bulk Reef Supply
Changes from Blue to Amber when exhausted
Anion Single Bed Color Changing DI Resin is great for people that want to be more efficient with their deionization resin usage. Single bed resins do require the use of a cation and anion resin followed by a mixed bed resin, but produce much better results and are much more efficient!
Two Sizes Available:
1.4 lb Single Cartridge Refill
8.1 lb Bulk Package - up to 6 single cartridge refills
Reverse osmosis systems can remove up to 99% of contaminants from your water, however, they can never remove 100% which is the overall goal for reef tank water. That is where deionization (DI) resin comes into play, by taking place as the last "filter" of a RODI system after the membrane. DI resin is ionically charged as either a cation (+) or anion (-) to exchange hydrogen or hydroxide molecules for contaminants like phosphate, silica, nitrate, sulfate, aluminum, iron, calcium, etc allowing you to achieve 0 TDS water for your aquarium and help eliminate any possible water quality issues. You may or may not know that there are multiple types of DI resin available from mixed bed to single bed resins that you can use depending on what the specific goal is for your water and what is in the water after the RO membrane.
Mixed or Single Bed
Single bed DI resins come in many different flavors, but at heart only contain a single cation or anion that makes up the entire media bed. Single bed resins are commonly used in household water softeners and other applications that require either the positive or negative ion to be removed and exchanged for hydrogen or hydroxide ions. The concentration of a single bed lets you focus on specific issues that you may have with your water without wasting extra resin like a mixed bed resins. Mixed bed resins contain both cations and anions in a single bed of media that will remove both positively and negatively charged ions from the water column. Mixed beds are very common in residential RODI system that is used for reef tanks and other types of aquariums since they are easy to use, but when it comes to efficiency and cost savings, single bed systems are the clear winners.
Cation or Anion
Cation = Positive Charge
Anion = Negative Charge
Choosing a single or mixed bed resin can be hard especially if you do not know exactly what is in your water or how a RO membrane will filter it. In most cases, you can use either the cation or anion mixed bed resins but may notice that a TDS meter is showing that the resin is exhausted before the color has changed completely. That is more than likely due to an excess of the opposite type of ion in your water when compared to the color changing dye used in that resin. If this is happening to you, changing to a resin with an opposite indicating dye of your current will help with visual monitoring as it becomes exhausted.
Mixed Bed Cation Resin (purple) - Most commonly used after single bed resins to polish any remaining contaminants. It contains both positive and negatively charged ions and will change from purple to amber as the cation resin is depleted. It is also perfect for single canister DI systems that have an excess of positively charged ions like calcium, magnesium, aluminum, ferrous and ferric iron.
Mixed Bed Anion Resin (blue) - The most commonly used resin in single or dual canister RODI systems and contains both negative and positively charged. The anion beads contain a blue color changing indicator that will turn to an amber color when it is exhausted. This resin is excellent for systems that have an excess of negatively charged ions that are not removed by the membrane, like phosphates, nitrates, sulfates, etc.
Single Bed Cation Resin (purple) - Contains only cation beads that focus on removing positively charged ions from the water that passes through it. As the resin becomes depleted it will change from a purple to amber letting you know at a glance when it is depleted. This is most commonly used as the first stage in a single bed DI system.
Single Bed Anion Resin (blue) - Anion resin focuses on removing negatively charged ions and has a blue color changing dye that will change to amber as it becomes depleted. Single bed anion resin is commonly used as the second stage in a single bed DI system.
A majority of DI resin has a color changing indicator that will change to a light amber color as the resin becomes exhausted. The dye is simply a pH indicator that is stable at high or low pH levels but will become translucent as the pH of the resin becomes neutral and the resin becomes exhausted. With single bed resins, there are some instances where your water may have a high or low pH, and can cause the color indicating dye to not become translucent, and that is why it is imperative to use a TDS or conductivity meter to know exactly when your resin is exhausted.
High pH water may interfere with the indicating dye contained in anion (blue) single bed resin.
Low pH water may interfere with the indicating dye contained in cation (purple) single bed resin.
Long Shelf Life
BulkReefSupply.com takes pride in the proper packing of our DI Resin. DI resin begins depleting when exposed to air. To avoid this, we package all of our DI resin in foil-lined 4mm Mylar bags AND vacuum seal it so no air is left in the package to deplete the resin while it is waiting to be used. Our resin can remain packaged this way for 2 years without losing its capacity. Our bulk DI bags are perfect for reefers who process a lot of water or otherwise go through resin quickly. Keep in mind once the vacuum seal is opened the resin can start to deplete. Otherwise, purchase the single refill packs for optimal freshness up to two years.
Polymer Structure: Styrene/DVB
Base Type: Strong
Polymer Type: Gel
Functional Group: Trimethylamine
Physical Form: Spherical Beads
Ionic Form (as shipped): Hydroxide
Total capacity: >1.0 meq/mL (OH Form)
Water Retention: 55 to 60 percent (OH Form)
Screen Size Distribution: 16 to 50 (U.S. Mesh)
Maximum Fines Content: 1 percent (less than 50 Mesh)
Minimum Sphericity: 93 percent
Uniformity Coefficient: 1.6 (Approximate)
Resin Color: Blue
To get maximum life from your DI resin please takes the following steps
- Ensure optimal operation of your RO membrane. The higher your membranes rejection rate the fewer TDS your product water will contain resulting in longer lasting resin. The best way to keep the membrane rejection rate up is to monitor and change your prefilters appropriately as well as maintain at least 50psi going into the membrane.
- Ensure the resin is packed in the cartridge securely. The resin should be packed very tightly. When squeezed, there should be almost no flex to the cartridge.
- The initial couple minutes of water from your RO membrane will always be high, this is commonly referred to as TDS creep. Diverting the first few minutes of water down the drain can often greatly reduce DI resin consumption.
- Maintain low levels of carbon dioxide in your water supply. Excess carbon dioxide will deplete DI resin quickly. If you are depleting resin quickly and have already: addressed the two options above, excess carbon dioxide is the likely culprit. You have two choices:
- Collect the water coming from your RO system in a large container, add a powerhead or airstone and allow the CO2 to gas off. Then pump the water through your DI resin.
- Skip all that mess and just buy resin in bulk.
|Molecule Name||Ionic Charge||Removed By|
|Ferric Iron||+2||Cation Resin|
|Ferrous Iron||+3||Cation Resin|
This is One of Two Stage.. You CANNOT use it alone! By Kurt on 5/8/2019Kurt would recommend this product to a friendHey folks, for those of you who had bad luck, I highly suspect you didnt understand what you bought. This DI Resin is meant to be run in conjunction with the Cation Resin in a separate stage. YOU CANNOT RUN THIS BY ITSELF! all the Cation ions will not be removed if you do, thus your TDS will be elevated.
Also, I will note that if you have a diatom problem, and have silicates in your water (I apparently do). using a two stage DI (Anion first, Cation second) is how you can help remove the silicates. The Silicates are removed by the Anion, and for most of us, using a mixed bed (especially if its partially depleted) will not suffice.
Much More Efficent By Simon on 2/26/2019Simon would recommend this product to a friendThis is the resin that I go through. Three or four anion to one cation and mixed bed. Has a slight odor to it but hardly the 'stink' that some represent.
Very good product By Perry on 1/8/2019Perry would recommend this product to a friendMy RO DI filter consists of a particulate filter, a carbon block (probably don't need, on very clean well water) an RO membrane (with pressure assist pump) 1 Cation canister, 1 Anion canister and 1 mixed bed resin chamber as a final polisher. I go thru a fair amount of the Anion resin compared to the other 2, but TDS are 0. I will definitely continue to use this product.
Works great By Andrew on 6/24/2018Andrew would recommend this product to a friendI have very high TDS water (~500 ppm) and as a result I used to burn through a lot of DI resin. So much that I gave up producing water with a TDS of 0 ppm. Now using a pro series anion cartridge in series with a pro series mixed bed cartridge I can easily produce water with a TDS of 0 ppm, with manageable costs. I usually comsume three anion cartridges for every pro series mixed bed cartridges.
The pro series anion cartridge does smell though, but it doesn't bother me as I usually fill my cetridges outdoors so there is adequate ventilation.
I have no doubt this works By Bryan on 6/2/2018Bryan would recommend this product to a friendWith all BRS products you are going to get very quality that works!! I am certain that this product will be no different. However, I have to warn you. This product here, STINKS SO BAD!!!! My wife and sister-in-law had to run up stairs practically throwing up from the smell. My windows are still open and the smell is just everywhere, through out the house. If you open this be sure to do this outside. I did this in the basement, it's been 2 hours, and I'm still smelling it.
Part of my RO/DI uprade to 6 stage from 4 By Allen on 5/6/2018Allen would recommend this product to a friendAs stated by Jared, it works. With my present 6st. triple TDS meter setup, I know if my carbon or membrane are a problem. After 3 months the Cation has not shown a hint of color change and the Anion has only shown about 3in. of color change. I am extremely confident in my present setup, I may add a silicate block or filter in the future. I've made a little over 250 gallons of 0 TDS water with this setup (not including reject water)
Response - Horrible! By HH on 3/28/2018 By Jared on 4/26/2018Jared would recommend this product to a friendIf used correctly then this product is FAR superior to the standard Mixed Bed DI Resin. YES it smells, and YES it is for removing negatively charged Ion based contaminants ONLY. This is roughly HALF of the total contaminants we need to remove from the source water to make actual 0 TDS RODI water. The other half are positively charged and need a Cation based resin directly BEFORE this resin. Please refer to the BRS Video documenting the correct way to setup these DI Pro based single Resins, This is why a "mixed bed" resin is a set it and forget it method. Using Cation and Anion based resins is more work, but you will be saving money in the long run by utilizing only what you need. Please research before you post a negative review. The BRS team works hard to sell the correct products, a quick Chat will alleviate any misconception of a product. and possibly benefit from a better choice for your setup.
Horrible! By HH on 3/28/2018HH wouldn't recommend this product to a friendI wanted to try a different DI resin in my RO system because I was experiencing a phosphate issue in my tank. I heard good things about it so I went for it and then I bought a TDS meter. I changed my media to this stuff and first of all this stuff stinks badly. Hooked everything back up and even ran it for a few days and my TDS read 28 to 40, yes it was going up. The other filters were changed a month ago and were fine. I got frustrated and put the old media back in and retested it and my TDS read 0. What a complete waste of money. I wasnt going to put that in my salt tank. Turns out my phosphate test kit was expired and I didn't need to replace anything.. too bad I didn't know that sooner. I purchase cheaper filters and media somewhere else already, apparently more expensive stuff doesn't always work. The saying "you get what you pay for" does not apply with this product!
Last way longer than Bulk Deionization Mixed Resin By Sheen on 3/23/2018Sheen would recommend this product to a friendI’m using this product with 10" Big Blue (Clear) Reverse Osmosis Canister. It seems to last a long time. My RODI system produced over 400 Gallons of 0 TDS RO water over the course of last 4 month and the resin finally started to change color at the bottom. Before changing to Cation/Anion DI resin, I was going through the DI resin a lot but with current rate, I can go for over a year for sure. This resin lasts way longer than Bulk Deionization Resin (Color Changing). I’m very happy with this product.