- Home /
- CPR Nano Tumbler Media Reactor
No related items recommended for this product.
Nice little tumbler By shawn on 7/1/2014shawn would recommend this product to a friendI have it in the back of my Nuvo 38 gal. Slim design, low flow. Other reviews are accurate. It works well but can have trouble with smaller media. The thin design does work well for sliding into the back of smaller tanks/ refuge.
Could be better By Jason on 2/3/2014Jason would recommend this product to a friendI used this for BioPellets on a 14 gallon BioCube. The stock pump wasn't strong enough to keep a minimal amount of BioPellets tumbling. I replaced the stock Rio Plus 90 with a Rio Plus 180 and it resolved the problem. Since it already ships with a flow control valve it would be better off they shipped it with a Rio Plus 180 from the start..
Nice little media reactor - within limits By raysun on 10/14/2013raysun would recommend this product to a friendAll of us reefers trying to emulate the ocean in a teacup of a nano tank are constantly striving to keep things stable. Small form factor media reactors are a lifesaver, but can also be a bit of a boat anchor. The CPR Nano Tumbler is a case in point.
I bought 2 Nano Tumblers for a 16 gallon SPS tank.
This is a typical, quality-assembled CPR product. Its simple design is well thought out and is intended to be used immersed in a filter chamber of an all-in-one nano system (or for the lucky, a nano sump.) Water flows in from the bottom, is diffused into the media chamber, and exits via the grate/screen orifice at the top, then re-enters the aquarium by flowing down the outer surface of the reactor.
Right out of the box, it's apparent the Nano Tumbler was designed for large pellet media - like nitrate reducing bio-pellets. The diffusion plate and bottom chamfer of the media chamber tumble them nicely. The little Rio pump with control valve dials in flow rate easily. The pump is quiet under load.
When using other media the unit's performance varies. (To be fair, most all media reactors start suffering as the media becomes finer grained.)
Large pellet carbon is no problem.
Small pellet carbon and GFO require additional sponges and screening that are not included. CPR sells a small media kit for a few bucks, but when I ordered them from CPR for the Nano Tumbler, I received kits for the larger Mini Tumbler. These don't fit the Nano without re-cutting and fitting. The medium porosity sponge and top screen kit work fine for media like BRS carbon and standard GFO (and others too, no doubt, but that is what I tested.)
The Nano Tumbler fitted with CPR fine media kit was an abject failure in my ultimate media reactor torture test - fluidizing Seachem Purigen. Purigen is a great product, but the super-small, slippery balls are a pain to contain. When loaded into the Nano Tumbler with fine media kit installed, Purigen blew right through the sponge and ended up jammed against the top fine media screen. An extremely low flow rate will allow this stuff to stay suspended in the media chamber, but once the unit is turned off and it settles onto the bottom sponge and works it's way through to the pump volute. Eventually, Purigen found it's way into the display tank. A much finer pore sponge would certainly help here. Also a fine media kit purpose-cut for the Nano would be a blessing.
One other struggle I had was specific to my setup, but others may be impacted as well. I was hoping this unit would fit into my Innovative Marine Nuovo 16 filter chamber. Mounted on the Rio, the unit is about 1 1/2" too tall. I mounted it on a Tunze Universal pump Mini (5024.04) and the height was perfect. I know I could have gone with the IM marketed media reactor, but just didn't want to spend twice as much. Guess I'll have to bite the bullet here.
All in all, this is a nice, simple media reactor that is easy to set up and load media - as long as it's not too fine. It's quiet and fairly easily to maintain. The media fluidizes nicely and circulates through the reaction chamber in a nice co-current / counter-current motion.
I'm keeping one for a GFO reactor, but this tank doesn't need a nitrate bio-pellet reactor, so the 2nd one is going back.
Previously Asked Questions
by Joe on February 25, 2014, @2:38 PM
does the water just flow back into the aquarium over the top, or are you supposed to run a protein skimmer off of it. I can tell in the video what you have inside the tumbler.
Bulk Reef Supply Hi Joe,
That is correct, its meant to be used in tank as the water flows straight up and over the top back into the tank. The video is a video done by CPR and happens to use biopellets (which make it really easy to see the way the water flows).
*Use a CPR Fine Media Kit or a mesh bag or filter sponge for use with fine media
Dimensions with Rio 90 Pump
- 3 1/2" L x 2 3/8" W x 11 3/8" H
- Total Capacity: 450 mL (Please account for space needed for fluidization)
- Biopellet Capacity: 225 mL (depending on density and fluidization)
- Energy Consumption: 3W
- Voltage/Frequency: 115V/60Hz
What's in the Box
- Rio 90 Feed pump and plumbing accessories
- Reactor Body
- Lid and cover assembly
- Coarse media screens
Deal of the Day!
BRS 4 Stage Value RO/DI System - 75GPDEnds in
Regular Price: $129.99
Special Price: $116.9900:00:00:00
- Bulk Reverse Osmosis Filters & Systems
- Bulk Dry Live Rock & Live Sand
- Aquarium Lighting
- Auto Top Off Systems
- Calcium, Alkalinity & Trace Elements
- Controllers, Monitors & Testing
- Filter Media
- Fish & Coral Foods
- Fragging Supplies
- Heaters & Chillers
- Pumps & Plumbing
- Salt Mix & Tank Maintenance
Skimmers & Reactors
- Internal Protein Skimmers
- External Protein Skimmers
- Hang On Skimmers
- Ozone Equipment
- Nano Skimmers & Accessories
- UV Sterilizers
- Sumps, Tanks & Refugiums
- Specials, New & BRS Gear
Send us your feedback
Let us know.
Phone Hours: 7am - 7pm CST M-Th
10am-4pm CST Friday
6325 Sandburg Road, Suite 400
Golden Valley, MN 55427 Map
View Larger Map 6325 Sandburg Road, Suite 400, Golden Valley, MN 55427