Excellent product By WingRider on 1/6/2014
WingRider would recommend this product to a friend
Added at same time I installed the 150g per day kit. Pump is quiet and pressure switch shuts the pump off once float Valle is triggered. Can tell difference in flow rate and hope to see waste drop off resulting in lower water bill.
highly recommend By steve on 12/16/2013
steve would recommend this product to a friend
Love this pump !! Im running a 150g per day 5 stage rodi unit...this pump boosted my water pressure from 40 psi to over 90 psi...i dialed it back to 68psi and all is happy. This pump is very quiet and the kit has everything you need to install it...maybe order some extra tubing depending where you put it.
Works Great By Christopher on 12/12/2013
Christopher would recommend this product to a friend
Neede this pump due to low water pressure. pushed pressure from 35psi to 88psi. Runs very quiet. Great product.
Booster pump By Bulldog on 12/12/2013
Bulldog would recommend this product to a friend
Great pump quiet and doubled my water pressure.
Great Product By Jennifer on 11/26/2013
Jennifer would recommend this product to a friend
Hooked this up in minutes and it took my psi from 40 to 90. Took it from a trickle to a strong stream. Fills my holding tank at least 3 times faster. I live in a small town that has water with tons of crud in it was burning threw DI resin. Before I would have to change resin after filling my holding tank which holds about 30 gallons after 3 times. Now I have so far filled it 4 times and only about 1/4 of the resin had started to change color.
Great Water Pressure By Sherman on 11/26/2013
Sherman would recommend this product to a friend
I have a well for our water system and the pressure has never been very good so when I added my 75 GPD RODI system on it, which had a pressure gauge, I was surprised that it showed I only had 20 psi, so I bout the Aquatec 8800 and my pressure went up to just over 90 psi. I use to fill my 55 gal resureve over a period of several days, now I get a gallon in about 30 min.
Performs as advertised By Geoff on 11/22/2013
Geoff would recommend this product to a friend
The pump saved on DI resin and it created enough pressure to send product water horizontally 30' and vertically 12' to my ATO reservoir at a rate of 3 gallons per hour. I'm very glad that I bought this pump!
Simple and effective By Ken on 11/14/2013
Ken would recommend this product to a friend
I live on a well, 35-55 psi cycle. Attached the pressure gauge (sold separately) before the membrane and only 30 psi. Hooked up the pump, 5 minute job, and now I'm at 80 psi going into the membrane. Output went from a trickle to nice stream. Will be interesting to see how long it takes to fill my 25 gal WC container this weekend. At the tap for our drinking water the flow is more than doubled. Excellent product.
works great By Ed on 11/7/2013
Ed would recommend this product to a friend
I have about 37 psi out of my faucet, and made 1 gal about a half hour or more , now it's at 80 psi and 1 g a l in. About 15 minutes. My concern is that the Gage was going up to 90 psi as. I went along making water. I turn it down to 60. I don,t know which numbers I should watch, the outer numbers or the inner ones ?? Otherwise I'm very satisfied.
A must have By Sven on 11/7/2013
Sven would recommend this product to a friend
My Tap water pressure was running about 40 PSI. Ever since I bought this and adjusted my PSI to ~70 PSI I now produce product water 2-3 times faster... and my DI Resin lasts longer as well!
Works great By Chuck on 11/4/2013
Chuck would recommend this product to a friend
This is just what I needed. I had a little over 37psi before I added this pump. I am now running at about 80psi now. Works great.
Great Investment to a RODI system By Kha on 11/2/2013
Kha would recommend this product to a friend
I had 45psi on my 75gph + 150gph upgrade RODI system until I added this pump. My psi is now 82-ish. Working great so far! Very easy to assemble and BRS already has a video on the installation (not that you would really need it). The pump makes some noise (very little) and vibration as all pumps do. The bracket seems to help out a bit. Not very concerned about the noise level since its going to be installed in a basement/ garage area. Wished the transformer had mounting hardware for the wall as the RODI and booster pump does. It has 4 rubber feet that sits on a horizontal surface. Not a big deal and not worth dropping any stars.
A MUST HAVE!!! By Megan on 10/18/2013
Megan would recommend this product to a friend
A must have!!! Nice to see the water quicker!! Life saver
What took me so long! By Turf on 10/15/2013
Turf would recommend this product to a friend
This is awesome, consistent 80psi to my filter so everything works unbelievably better, faster and more consistent. Wish I bought this years ago.
Stop what you're doing and BUY THIS UNIT NOW By Carlos A. on 10/6/2013
Carlos A. would recommend this product to a friend
I've been frustrated to no end trying to fine tune a similar setup I bought from another vendor. Their unit included the same pump but didn't include a pressure switch and instead required the endless fine-tuning of several different variables (turn this dial down, turn the other up, but not too much, etc...), which took hours and hours and it never ever came even close to working as well as this did right out of the box. This is a set-it-and-forget-it solution that is SO MUCH EASIER. I had thrown away my previous set up and I am so glad I bought this one. My 150 gpd RO system went from producing a very slow drip (maybe 25 gallons/day) to now producing a solid stream of very close to the 150 gpd max. More importantly, the ratio of good to bad water is much better. Buy this now. It's the same kind of quality you find with Tunze and Bubble King.
I highly recommend combining this with the: Aquatec Auto Flush Flow Restrictor, also available on this site. That makes it truly an automatic system that will save you tons in filters and water over the long run.
Aquatec is brilliant for having designed this. Bravo.
excellant value and a must have time saving pump By happy reefer on 10/6/2013
happy reefer would recommend this product to a friend
llike everyone else I had low psi only 40 going into my 5 stage brs ro/di unit and only making 2 gallons of water at about 35min a gallon and replacing resin at a quicker rate then I would think should be needed so my descision became a cost saving idea to finally purchase so I lucked up it just so happen a fellow Michigan reefer was selling one for $70 with power supply and pressure switch so it was a no brainer when I offered a trade and only spent $50 and with the rubber feet you cant really here it running I went from psi of 40 to 60 and with the adjustment screw I now have 80 psi and producing 1 gallon every 15-18 min 0 tds water
Great Product By Brian on 9/10/2013
Brian would recommend this product to a friend
I was ripping through DI resin like crazy. With the addition of this pump, I get much more life out of my resin.
A must for any RODI system By Timothy on 9/3/2013
Timothy would recommend this product to a friend
The Aquatec 8800 booster pump is a must for any RODI system. I had adaquate water pressure half of the year before adding the pump- now I am making water at my systems capacity more efficiently even in the winter. The pump will pay for itself over time and is easy to integrate into your current system.
Problem Solver! By Mark on 9/1/2013
Mark would recommend this product to a friend
Water pressure out of the tap was 25-30 psi. Not good, Ordered this kit from BRS and now I'm at 63 psi with plenty of room to spare. Problem solved and the best price.
A must if you have your own well By Tom T on 8/7/2013
Tom T would recommend this product to a friend
I live in the country with my own well. I connected my RO/DI system and the pressure swing between 24 and 32 psi. I added this pump and now my pressure is between 88 and 90 psi. This has increased the my RO/DI water output tremendously.
Need a boost By Little man on 8/6/2013
Little man would recommend this product to a friend
I got the aquatec 8800 kit from brs I hooked it to my brs ro di system and what a difference it made . My water pressure went from 35 psi to 95 psi . Also my brs di resin last longer now. I also got the pressure switch and float valve which took the guess work out when my water storage container was full . No more check every hour to see if it is full. It shuts the pump off automatic when it reach a certain level. Thanks brs for making reefing easier
Pricey investment that's worth every penny. By Jeffrey on 8/4/2013
Jeffrey would recommend this product to a friend
I was running 40psi with my 75gal ro system in my apt. adding this pump with the 150 gal upgrade, I couldn't be happier running at 80psi and using up less resin than before. Someone like me who doesn't have a lot of time to spend making ro water this gets the job done quickly.
Must have for low pressure By Aaron on 6/29/2013
Aaron would recommend this product to a friend
Having well water only gave us a maximum of 45psi and dropped to around 30psi before the well pump kicked in. Water production was horrible and waste ratio was 4:1. With this pump we are at a consistent 85 to 90 psi and waste ratio has improved significantly. This pump is a must have for well owners. Hook up was easy, although I placed the pump right before the membrane instead of the first sediment filter. Works perfect.
booster pump By Billy on 5/30/2013
Billy would recommend this product to a friend
If you ain't got a booster pump for your ro system you need to get one. Talking about putting out good amount of water.
Works Great By Tom on 5/20/2013
Tom would recommend this product to a friend
I didn't have enough pressure for my RO system. Very easy to install and now I'm getting all the water I need.. Works great!
Awesome in almost every way, maybe a little loud By tramboneplayer5 on 5/18/2013
tramboneplayer5 would recommend this product to a friend
My 75GPD 6-stage chloramines RO/DI kit was more like a 35-40GPD system until I got this pump. Water used to trickle out so slowly. The TDS going in to the DI stage was high as well and I was tearing through DI resin like crazy. When I added this pump, I had to turn it down a little to get back to 80psi by using the small hex screw in the center of the top and turning it counter-clockwise. Water shoots out so much faster (80-90GPD) and the TDS is lower out of the RO stage. The only mistake was mounting this to a wall - the vibration is carried through the house and it makes it pretty loud. I will try moving it to another surface that is de-coupled from the wall.
Does the job By den75 on 5/12/2013
den75 would recommend this product to a friend
Excellent pump. PSI went from 32 to 85 immediately increasing my RO/DI output and lessening my waste water.
Excellent product By abi on 4/29/2013
abi would recommend this product to a friend
Great pump! My municipal water pressure was at 29 psi this pump brought it all the way up to 60 psi with room to increase the pressure! Excellent for my 150 gpd rodi water saver plus unit.
Great product By retnip on 4/15/2013
retnip would recommend this product to a friend
This is really a neat little pump, it comes with everything you would need to boost the pressure to your ro system. It boosted my pressure from 45lbs to around 90lbs. It is a little noisy and needs to be mounted to something so it dosnt walk around. Its easy to hook up, just snip out a short section of supply hose, and a short section of the hose that goes to your storage tank to insert the pressure switch. When you float rises, the pump will shut off automatically.
Works Great! By Christy on 4/13/2013
Christy would recommend this product to a friend
This works great! Bought the 75gpd RO/DI unit and when I got it set up I was VERY disappointed to find I only had about 30 psi and a periodic trickle of filtered water coming out. Purchased the booster pump and patiently (not really lol) waited for it to come so I could get rolling on curing the dry rock I previously purchased. Hooked it up and started getting nearly 100 psi!! Had to turn it back a little. Now pulling a steady 80 psi at 0 tds and have my rock curing in the basement!! :-) Next purchase might just have to be the converter kit to increase my unit to the 150 gpd now that I have the pump and know it could handle it!! :-)
great solved my low pressure problem By chen yang on 3/30/2013
chen yang would recommend this product to a friend
before the pump i was getting around 45 psi at best. after I installed this , which was super easy! I got around 95 psi. so i have to dialed down a bit to around 80 psi. i am really happy that i can finally utilize full of my ro di unit. none of the other big aquarium online store offer booster pump kit and instrucitons. thank you brs!
Time is money By greenwizard on 3/25/2013
greenwizard would recommend this product to a friend
doubled my water output.
Wonderful! By Terrie on 3/13/2013
Terrie would recommend this product to a friend
Absolutely worth every $1 spent for it. My water makes in 1/2 the time it use to and I do go through less Di Resin :)
Great Product By Toby on 3/12/2013
Toby would recommend this product to a friend
I get 60psi from my municipal water supply. When someone is using water, it's alot less. This eliminates the problem. Im getting 90psi constantly. 1# Doubles production 2# Better rejection rate.,reduces TDS before the DI canisters from 14 before the pump to 7-8 TDS. Saves DI Resin.
Well worth it. By Bob on 2/24/2013
Bob would recommend this product to a friend
I was only getting 42 PSI with my home water pressure on a 75 GPD
RO/DI unit. I added a 150 GPD upgrade kit and this pump and get a steady 88 PSI. It is a very quiet pump and fills my 32 gal. can in half the time. I am very pleased with this product.
Easy Installation By Jeremy on 2/22/2013
Jeremy would recommend this product to a friend
My pressures were borderline with running a second membrane. This was installed very quickly and the output was improved drastically.
Superb By Edward on 2/15/2013
Edward would recommend this product to a friend
Was getting only 28-30PSI before getting this unit. I live in an old factory converted to a high rise apartment complex.
I initially looked on ebay for a cheap unit, but after adding it all up, you really arent saving much money. I spent the extra $20 or so on the Aquatec 8800 kit from BRS and am very happy that I did.
After installing this, I get a steady 90PSI. My RO/DI output is a steady stream of water where it used to be a couple drips per second.
Pump is quiet, installation a breeze. I highly recommend this product.
Pump it up By LOUIS on 2/15/2013
LOUIS would recommend this product to a friend
So this certainly improved my RO/DI unit in combination with the 75gl extra membrane. I wasn’t getting the amount the video stated till I understood that I needed the extra pressure. I am glad I got the full kit and not just the pump. I like it when all the parts needed are on hand and just to be installed instead of tracking down all the parts to actually use the pump. Less water to waste and collect for other use’s helps with the water bill.
Allows me to use my RO/DI Unit with a Well By Miles on 2/13/2013
Miles would recommend this product to a friend
I purchased this kit when last year when I moved to the country. I use it in conjunction with the Auto Shutoff Kit and am able to let my RO/DI system run continuously (if I forget to turn it off). This pump has brought me up from 40 PSI to 70PSI. I initially had to adjust it the output down from 90 PSI but have not had any problems with it. It is by no means silent, but I have it in my unfinished basement and can't hear it upstairs.
A must have for marginal water pressure. By Al on 1/28/2013
Al would recommend this product to a friend
Yeah - your bill is adding up and it seems to be a huge increase to the cost of your new system. I was getting 55 psi out of my house water, and I'm glad I pulled the trigger here. What I have found is that anything you can do to reduce the amount of waste water (rejection rates) the better - I haven't regretted this purchase at all - in fact, I want to say its a must, especially if you are doing the 150gpd upgrade kit.
Good pump, a little noisy By Jerry on 1/23/2013
Jerry would recommend this product to a friend
I put this pump on my system to boost the pressure, works good for that but is a bit noisy.
A must have with a RO uinit By RANDY on 1/23/2013
RANDY would recommend this product to a friend
This pump does everything I expected it to do. I did not have enough water pressure to stop the production of waist water. Now my system works flawlessly and faster to boot!
Great Product By Jeremy on 1/2/2013
Jeremy would recommend this product to a friend
I was using Di and first stage filters like crazy. Now with this kit was just what the doctor ordered! Easy to install and it has everthing you need to boost your system!
A must have By Robert on 12/30/2012
Robert would recommend this product to a friend
Pressure stays constant no matter what, people showering, laundry, dishwasher running.
What A Difference! By PATRICK on 12/14/2012
PATRICK would recommend this product to a friend
I added this to my BRS Water Saver Plus 150 Gallon Per Day unit. Before the pump, I was pulling 25-40 PSI from my well; afterwards, I have a steady 90 PSI. It fills my 30 gallon trash cans super fast. The pump is very quiet and I now have it mounted under my sink with the RO unit.
A MUST have for low preasure By John on 11/19/2012
John would recommend this product to a friend
After adding my RODI unit my pressure was only 35-40 PSI which was not getting me anywhere on making my water. After adding this pump to my system I now have a SOLID 90PSI when making water.
This unit is extremely quiet and well built – A must have!
without a doubt its a great investment By jorge on 11/2/2012
jorge would recommend this product to a friend
So i got the pump yesterday and by 6:30pm i was filling my 55gallon and a 64gallon drums, i am very satisfied by how quick they were filled. I really apreciate your business and shipping is fast too! AAA+++++
Can't beat for winter preparation! By Brandon on 10/18/2012
Brandon would recommend this product to a friend
This pump is even better than I expected. It was simple to install. Not to mention, it's much quieter than I had expected! I thought as soon as I plugged this thing it, it would sound like a small air compressor, man was I wrong! I purchased this pump because I run a 90gpd piggy-back. My home water pressure is around 60psi in the summer, however, with the winter coming along, the cold water drastically reduces the pressure. I see such a pressure drop because this unit is setup in an outside Rubbermaid storage shed specifically for hobby items. This includes two 32 gallon Brute trash cans for fresh and saltwater mix. The water runs from a 75 foot hose from the house, to the RO/DI unit. Last year, I experienced pressures so low during the winter, I had to take my additional piggy-back membrane off and just run one. This year, with the additional pressure from the pump, I'll be prepared for winter! I highly recommend this product. Not to mention, you can't beat BRS' price on this!