Great Product By Jennifer on 11/26/2013
Jennifer would recommend this product to a friend
Hooked this up in minutes and it took my psi from 40 to 90. Took it from a trickle to a strong stream. Fills my holding tank at least 3 times faster. I live in a small town that has water with tons of crud in it was burning threw DI resin. Before I would have to change resin after filling my holding tank which holds about 30 gallons after 3 times. Now I have so far filled it 4 times and only about 1/4 of the resin had started to change color.
Great Water Pressure By Sherman on 11/26/2013
Sherman would recommend this product to a friend
I have a well for our water system and the pressure has never been very good so when I added my 75 GPD RODI system on it, which had a pressure gauge, I was surprised that it showed I only had 20 psi, so I bout the Aquatec 8800 and my pressure went up to just over 90 psi. I use to fill my 55 gal resureve over a period of several days, now I get a gallon in about 30 min.
Performs as advertised By Geoff on 11/22/2013
Geoff would recommend this product to a friend
The pump saved on DI resin and it created enough pressure to send product water horizontally 30' and vertically 12' to my ATO reservoir at a rate of 3 gallons per hour. I'm very glad that I bought this pump!
Simple and effective By Ken on 11/14/2013
Ken would recommend this product to a friend
I live on a well, 35-55 psi cycle. Attached the pressure gauge (sold separately) before the membrane and only 30 psi. Hooked up the pump, 5 minute job, and now I'm at 80 psi going into the membrane. Output went from a trickle to nice stream. Will be interesting to see how long it takes to fill my 25 gal WC container this weekend. At the tap for our drinking water the flow is more than doubled. Excellent product.
works great By Ed on 11/7/2013
Ed would recommend this product to a friend
I have about 37 psi out of my faucet, and made 1 gal about a half hour or more , now it's at 80 psi and 1 g a l in. About 15 minutes. My concern is that the Gage was going up to 90 psi as. I went along making water. I turn it down to 60. I don,t know which numbers I should watch, the outer numbers or the inner ones ?? Otherwise I'm very satisfied.
A must have By Sven on 11/7/2013
Sven would recommend this product to a friend
My Tap water pressure was running about 40 PSI. Ever since I bought this and adjusted my PSI to ~70 PSI I now produce product water 2-3 times faster... and my DI Resin lasts longer as well!
Works great By Chuck on 11/4/2013
Chuck would recommend this product to a friend
This is just what I needed. I had a little over 37psi before I added this pump. I am now running at about 80psi now. Works great.
Great Investment to a RODI system By Kha on 11/2/2013
Kha would recommend this product to a friend
I had 45psi on my 75gph + 150gph upgrade RODI system until I added this pump. My psi is now 82-ish. Working great so far! Very easy to assemble and BRS already has a video on the installation (not that you would really need it). The pump makes some noise (very little) and vibration as all pumps do. The bracket seems to help out a bit. Not very concerned about the noise level since its going to be installed in a basement/ garage area. Wished the transformer had mounting hardware for the wall as the RODI and booster pump does. It has 4 rubber feet that sits on a horizontal surface. Not a big deal and not worth dropping any stars.
A MUST HAVE!!! By Megan on 10/18/2013
Megan would recommend this product to a friend
A must have!!! Nice to see the water quicker!! Life saver
What took me so long! By Turf on 10/15/2013
Turf would recommend this product to a friend
This is awesome, consistent 80psi to my filter so everything works unbelievably better, faster and more consistent. Wish I bought this years ago.
Stop what you're doing and BUY THIS UNIT NOW By Carlos A. on 10/6/2013
Carlos A. would recommend this product to a friend
I've been frustrated to no end trying to fine tune a similar setup I bought from another vendor. Their unit included the same pump but didn't include a pressure switch and instead required the endless fine-tuning of several different variables (turn this dial down, turn the other up, but not too much, etc...), which took hours and hours and it never ever came even close to working as well as this did right out of the box. This is a set-it-and-forget-it solution that is SO MUCH EASIER. I had thrown away my previous set up and I am so glad I bought this one. My 150 gpd RO system went from producing a very slow drip (maybe 25 gallons/day) to now producing a solid stream of very close to the 150 gpd max. More importantly, the ratio of good to bad water is much better. Buy this now. It's the same kind of quality you find with Tunze and Bubble King.
I highly recommend combining this with the: Aquatec Auto Flush Flow Restrictor, also available on this site. That makes it truly an automatic system that will save you tons in filters and water over the long run.
Aquatec is brilliant for having designed this. Bravo.
excellant value and a must have time saving pump By happy reefer on 10/6/2013
happy reefer would recommend this product to a friend
llike everyone else I had low psi only 40 going into my 5 stage brs ro/di unit and only making 2 gallons of water at about 35min a gallon and replacing resin at a quicker rate then I would think should be needed so my descision became a cost saving idea to finally purchase so I lucked up it just so happen a fellow Michigan reefer was selling one for $70 with power supply and pressure switch so it was a no brainer when I offered a trade and only spent $50 and with the rubber feet you cant really here it running I went from psi of 40 to 60 and with the adjustment screw I now have 80 psi and producing 1 gallon every 15-18 min 0 tds water