Easy Install By Benjamin on 3/11/2015
Benjamin would recommend this product to a friend
It works, my pressure was around 40psi without the booster. I set it up and its running at 75psi, I did dial it down a little from the factory setting. I was able to install it in under 20 min. no problems. I have not had any issues with the pump makeing excessive noise but i did take the time to put a issolation pad under it and mounted it to the wall.
Really is a must have item By Shawn on 2/26/2015
Shawn would recommend this product to a friend
I run this on a BRS 6 stage universal RO DI set up with a 150 gallon a day upgrade. I find it produces about 30% more water a day and no additional waste water. My house psi is 55 the pump increases the psi to nearly 90 and holds 90 even as the filters start to become used. Really a must have for 5 and 6 stage systems
Not bad but loud By DanDI on 2/18/2015
DanDI would recommend this product to a friend
I installed my 8800 on the wall in the garage. It vibrates terribly but I dont hear it once I shut the door. When it was in the laundry room, it was more obnoxious. Many say it is quiet, so I'm wondering if I have a defective one. It does do the job, however.
Great product By Evan on 2/12/2015
Evan would recommend this product to a friend
I bought a house a couple years ago. On city water and my PSI sways from 40-45psi. Finally got this booster pump, and I was able to raise my psi to my unit's recommendation of 80psi. I had to dial down the booster pump from ~85psi, and it was very easy with a 1/16 allen wrench.
I keep my RO/DI system in my laundry room, close to the living room, and the sound is barely noticeable (pump is mounted). Note, pre-filter will vibrate too, make sure to secure that.
Speaking of the pre-filter, BRS should offer this kit with it instead of the pressure switch, and make the pressure switch an option. Since EVERYONE should be running it with the prefilter, and not everyone needs a pressure switch.
An excellent investment that will save you time, water, and di resin.
Boosts! By Mike on 2/6/2015
Mike would recommend this product to a friend
Really improved my GPD output, especially during the winter months when production usually decreases. Auto Shut Off feature works well.
Well worth the cost, if you have lower pressure By Ram on 1/27/2015
Ram would recommend this product to a friend
My Spectrapure CSPDI 90 gal system was running at about 45 PSI for the longest time. A gallon of water would take more or less 30 minutes to filter through... not cutting it! I added this booster pump and have never looked back. Essentially doubled my pressure and cut the time to produce a gallon in half.
Operation is relatively quiet and setup really couldn't be any easier. Highly recommend you just buy this thing.
Works great, but it is loud By Ken on 1/22/2015
Ken would recommend this product to a friend
My home water pressure was 48 PSI and after I installed this booster it was at 98. I now run a 150 GPD RO system with no problems. I can however hear this pump running from my basement as a dull hum throughout the 1st floor of the house.
Does the job, but super noisy! By Warren on 1/16/2015
Warren wouldn't recommend this product to a friend
This thing vibrates my entire house's plumbing. It is awfully unpleasant. One of my least favorite purchases from BRS. I'm going to try a Gold Series Shurflo instead. My entire family complains about this pump. We can hear it all the way from the basement to the top floor. The pump itself isn't that noisy, but it has some sort of pressurized wave effect on the plumbing.
Good product By Big C on 1/10/2015
Big C would recommend this product to a friend
My pressure was only 35psi but when I hooked up pump it jumped to 90 psi. Easy to plumb n pretty quiet too. Highly recommended if u have low pressure or use the water saver option.
Worth it By David on 12/22/2014
David would recommend this product to a friend
Made my RO unit complete and gave me enough power to get the water I need. Simple hookup and operation.
super upgrade By Strych2 on 12/13/2014
Strych2 would recommend this product to a friend
Fantastic, well worth the buck! I have a 4 stage unit that was putting out less than 40 psi. Because of low water pressure filling my tank was a slow and argues process. This unit took my system up to 95 psi. I can produce water quickly the DAY of my water change!
super quiet By Michael on 12/13/2014
Michael would recommend this product to a friend
Kit is very easy to hookup, took less than 15 minutes and very very quiet. with this kit I'm not making water twice if not three times faster. Well worth the buy.
Must Have By Cap on 12/11/2014
Cap would recommend this product to a friend
Great pump, went from 55 psi to 80 on 5 stage, with auto shut off, di resin use is down also, very happy, no noise, very quiet.
Just Plain works great By Ryan on 11/30/2014
Ryan would recommend this product to a friend
I had low water pressure issues when I first installed my RO system so i ordered the booster pump kit and it completely took care of my problem and has worked with no problems what so ever since I installed it. Another great product
Booster pump By Joe on 11/5/2014
Joe would recommend this product to a friend
This pump is great. Easy to set up and helps lower my TDS due the the increase in pressure I guess. Also makes my Water twice as fast as before. Thanks BRS
would recommend By shdw2001h on 10/27/2014
shdw2001h would recommend this product to a friend
Easy to set up. when from 50 psi to over 80 psi. cut the time to fill my drum up from 5 hours to about 2-3 hours. Also it is very quiet.
Doubled my PSI By jeffrey on 9/20/2014
jeffrey would recommend this product to a friend
Just installed this on my RO/DI unit and my before PSI was 40 PSI and with this pump kit I am getting just above 80 PSI. I also installed my RO/DI unit inside a cabinet since I have mine outside under a deck. If you dont you will eventually get green algae problems in it. Keep it dark ;-) Have to order a bracket to be able to install another 10" canister for my DI resin so I do not yet know how the pump will effect the DI depletion. It seem to use DI resin fast when I had only 40 PSI. More to follow
Does a Great Job, but is far from quiet By Bert on 7/3/2014
Bert would recommend this product to a friend
This pump does a super job if you need the pressure for your RODI system as I did. Simply be aware it's far from silent when it operates. I can hear mine operating with it's fast chug-chug-chug in the other room with both the door to it's cabinet and that room closed.
Great Product By Brittany on 5/14/2014
Brittany would recommend this product to a friend
I purchased this kit for my RO/DI unit and I was amazed at how much more water this thing helps my unit produce. My home has a well and I was always sitting between 35-40 PSI. I purchased this pump and now it keeps my input at a constant 80 PSI. I did however have to turn the small screw on the top because when I initially hooked it up it was over 100 PSI.
Works as it should By lowtek on 5/9/2014
lowtek would recommend this product to a friend
I was only getting 45 lbs of pressure through my brs water saver system I received some time ago. Not wanting to run my r/o unit at half capacity and waste tons of water I waited till I got this booster pump. Well worth the 1 year wait. Pump is solid, heavy, made in the US and runs pretty quiet. Boosts my pressure to about 90 psi which is well over the recommended pressure so I'm a happy camper.
This is awesome coupled with the 150 gpd upgrade By jonathan on 5/9/2014
jonathan would recommend this product to a friend
I bought this pump with the 150 GPD RO upgrade and all i can say is wow. It went from taking half a day to fill my brute trash can to just over 3 hours. cant wait to see if and how much it cuts down my water bill
Worth the Investment...... By Tyler on 5/5/2014
Tyler would recommend this product to a friend
I went back and forth deciding if it was worth it to get this or not. After installing it and running it for a few weeks I have to say it is truly worth the price. I not only make water more efficiently, but waste a lot less as well. It is nearly silent when running and enables me to get the exact pressure I want.
Great Pump By Victor on 4/16/2014
Victor would recommend this product to a friend
Received this pump a few weeks ago, it raised my pressure to around 85 and is quite. I have it mounted on a small piece of plywood on the wall in my water closet.
It works By NH Dan on 4/10/2014
NH Dan would recommend this product to a friend
I just received this pump setup a few days ago. I also bought the 150 gpd upgrade with it. I am on a well and could only get about 40 psi. I hooked up the pump and pressure switch and I am getting a steady 70 psi. The pump is quiet and has really increased the water production.
It does what it's supposed to. Good product.
Rocks.. at over a 100 PSI By Chicago on 4/2/2014
Chicago would recommend this product to a friend
Ok.. this pushed my PSI from 48 on the incoming to over 100. Not sure since my gauge only goes to 100. I understand it is advertised to push water PSI to 115.
A must have By David on 3/25/2014
David would recommend this product to a friend
This a must have for your RO/DI unit.
Exceptionally Quiet By Phenganax on 3/12/2014
Phenganax would recommend this product to a friend
I was expecting this pump to be fairly loud and was concerned because of where I have it in my apartment; however, it was quieter than my Bak-Pak 2. I also have readings of 70 psi after my second membrane, I would highly recommend this product to anyone who wants to increase their psi or add a second membrane. I was also concerned that it would be too much pressure for my 15 gallon pressurized RO reservoir and that the pressure valve wouldn’t shut it off. Much to my satisfaction this has not been a problem, the whole system works flawlessly now!
Works great! By Bageezus on 2/27/2014
Bageezus would recommend this product to a friend
Really boosted my pressure. Works perfect. Took my pressure from 30psi to over 60!
Great By Adam on 2/9/2014
Adam would recommend this product to a friend
My RO/DI dripped out clean water but after using this pump is flows out as fast as the waste water. Huge improvement. Highly recommend if water pressure is your issue.
Works as Described By Tim on 2/6/2014
Tim would recommend this product to a friend
Cold winters in Canada showed me that I needed to up my system to 150 GPD. I only have 60 PSI out of the tap so I needed this pump. For my application it works great!! I had to actually turn down the pump as it increased my PSI past 100. I tuned it down to 80 - 82 PSI.
I will say the pump is a little louder than I'd like. The one thing that I'm not thrilled with is the noise of the PSI gauge. I have the default air filled gauge and the pump causes the dial to (flip flop) and that = noise. BRS support states that Glycerin filled gauge will nullify this. I have yet to purchase that.
Outstanding! By RiffeShooter on 1/17/2014
RiffeShooter would recommend this product to a friend
I purchased this with the 150GPD Water Saver RO/DI kit and I have to say, this is like adding a turbocharger to your water output! Has a consistent pressure of 85 psi and blows that water out. Another simple to install BRS product that saves the day!
Excellent value for your system By chris on 1/15/2014
chris would recommend this product to a friend
Before installing this my dual membrane system was operating at about 35psi. My system was producing about 50/50 product/ waste water. After installing this booster i am operating at 70psi and my water to waste production is around 75/25 product/ waste water. This thing is a must have if you want the highest efficiency possible out of your system.
Boosted PSI By Adam on 1/8/2014
Adam would recommend this product to a friend
My house has fairly low water pressure, around 40 PSI or a little under most of the time. I purchased this pump and now I am getting around 85 PSI. This will be perfect for when i order the 150 GPD upgrade for my RODI.
Excellent product By WingRider on 1/6/2014
WingRider would recommend this product to a friend
Added at same time I installed the 150g per day kit. Pump is quiet and pressure switch shuts the pump off once float Valle is triggered. Can tell difference in flow rate and hope to see waste drop off resulting in lower water bill.
highly recommend By steve on 12/16/2013
steve would recommend this product to a friend
Love this pump !! Im running a 150g per day 5 stage rodi unit...this pump boosted my water pressure from 40 psi to over 90 psi...i dialed it back to 68psi and all is happy. This pump is very quiet and the kit has everything you need to install it...maybe order some extra tubing depending where you put it.
Works Great By Christopher on 12/12/2013
Christopher would recommend this product to a friend
Neede this pump due to low water pressure. pushed pressure from 35psi to 88psi. Runs very quiet. Great product.
Booster pump By Bulldog on 12/12/2013
Bulldog would recommend this product to a friend
Great pump quiet and doubled my water pressure.
Great Product By Jennifer on 11/26/2013
Jennifer would recommend this product to a friend
Hooked this up in minutes and it took my psi from 40 to 90. Took it from a trickle to a strong stream. Fills my holding tank at least 3 times faster. I live in a small town that has water with tons of crud in it was burning threw DI resin. Before I would have to change resin after filling my holding tank which holds about 30 gallons after 3 times. Now I have so far filled it 4 times and only about 1/4 of the resin had started to change color.
Great Water Pressure By Sherman on 11/26/2013
Sherman would recommend this product to a friend
I have a well for our water system and the pressure has never been very good so when I added my 75 GPD RODI system on it, which had a pressure gauge, I was surprised that it showed I only had 20 psi, so I bout the Aquatec 8800 and my pressure went up to just over 90 psi. I use to fill my 55 gal resureve over a period of several days, now I get a gallon in about 30 min.
Performs as advertised By Geoff on 11/22/2013
Geoff would recommend this product to a friend
The pump saved on DI resin and it created enough pressure to send product water horizontally 30' and vertically 12' to my ATO reservoir at a rate of 3 gallons per hour. I'm very glad that I bought this pump!
Simple and effective By Ken on 11/14/2013
Ken would recommend this product to a friend
I live on a well, 35-55 psi cycle. Attached the pressure gauge (sold separately) before the membrane and only 30 psi. Hooked up the pump, 5 minute job, and now I'm at 80 psi going into the membrane. Output went from a trickle to nice stream. Will be interesting to see how long it takes to fill my 25 gal WC container this weekend. At the tap for our drinking water the flow is more than doubled. Excellent product.
works great By Ed on 11/7/2013
Ed would recommend this product to a friend
I have about 37 psi out of my faucet, and made 1 gal about a half hour or more , now it's at 80 psi and 1 g a l in. About 15 minutes. My concern is that the Gage was going up to 90 psi as. I went along making water. I turn it down to 60. I don,t know which numbers I should watch, the outer numbers or the inner ones ?? Otherwise I'm very satisfied.
A must have By Sven on 11/7/2013
Sven would recommend this product to a friend
My Tap water pressure was running about 40 PSI. Ever since I bought this and adjusted my PSI to ~70 PSI I now produce product water 2-3 times faster... and my DI Resin lasts longer as well!
Works great By Chuck on 11/4/2013
Chuck would recommend this product to a friend
This is just what I needed. I had a little over 37psi before I added this pump. I am now running at about 80psi now. Works great.
Great Investment to a RODI system By Kha on 11/2/2013
Kha would recommend this product to a friend
I had 45psi on my 75gph + 150gph upgrade RODI system until I added this pump. My psi is now 82-ish. Working great so far! Very easy to assemble and BRS already has a video on the installation (not that you would really need it). The pump makes some noise (very little) and vibration as all pumps do. The bracket seems to help out a bit. Not very concerned about the noise level since its going to be installed in a basement/ garage area. Wished the transformer had mounting hardware for the wall as the RODI and booster pump does. It has 4 rubber feet that sits on a horizontal surface. Not a big deal and not worth dropping any stars.
A MUST HAVE!!! By Megan on 10/18/2013
Megan would recommend this product to a friend
A must have!!! Nice to see the water quicker!! Life saver
What took me so long! By Turf on 10/15/2013
Turf would recommend this product to a friend
This is awesome, consistent 80psi to my filter so everything works unbelievably better, faster and more consistent. Wish I bought this years ago.
Stop what you're doing and BUY THIS UNIT NOW By Carlos A. on 10/6/2013
Carlos A. would recommend this product to a friend
I've been frustrated to no end trying to fine tune a similar setup I bought from another vendor. Their unit included the same pump but didn't include a pressure switch and instead required the endless fine-tuning of several different variables (turn this dial down, turn the other up, but not too much, etc...), which took hours and hours and it never ever came even close to working as well as this did right out of the box. This is a set-it-and-forget-it solution that is SO MUCH EASIER. I had thrown away my previous set up and I am so glad I bought this one. My 150 gpd RO system went from producing a very slow drip (maybe 25 gallons/day) to now producing a solid stream of very close to the 150 gpd max. More importantly, the ratio of good to bad water is much better. Buy this now. It's the same kind of quality you find with Tunze and Bubble King.
I highly recommend combining this with the: Aquatec Auto Flush Flow Restrictor, also available on this site. That makes it truly an automatic system that will save you tons in filters and water over the long run.
Aquatec is brilliant for having designed this. Bravo.