Great By ebushrow on 9/20/2013
ebushrow would recommend this product to a friend
I hated seeing all the waste water produced for such a small amount of RO/DI produced. This allows the ratio to be more acceptable by running the waste water through your 2nd membrane to pull out that much more. Great addition to your current unit and well worth the extra expense.
Great adon doubles output and cuts waste in half! By Saboken on 9/8/2013
Saboken would recommend this product to a friend
It was simple to setup once I looked at the Video the only thing that would have made the install better would be instructions included with the kit.
Worth it. By Jeffrey on 8/4/2013
Jeffrey would recommend this product to a friend
I bought the 75 gal ro system and was ok but didn't like the fact that my apt. water was only able to push 40psi. Needless to say burned through the resin quickly. I wanted to upgrade to this for a long time but could never afford the upgrade and pump. Now that I have them my water is pumping out quickly and couldn't be happier running at 80psi. Resin lasts longer which means it saves me money. Only wish I was able to afford everything a long time ago.
Save time and waste less By ScubaSteve on 6/28/2013
ScubaSteve would recommend this product to a friend
My wife and son bought this for me for fathers day and it really is the best present my son has gotten me. Water changes take half the time and apparently I am wasting less water. Installation was extremely easy because of the video BRS has made for us to watch. I think it took me 5 minutes and that was only because my unit is located in a tight spot under my sink. had i been able to just hook it right up without pulling out from under the sink it would have only take 2 minutes. I also save time when doing top offs. Thanks BRS you help make my life easier.
Happy By John on 6/6/2013
John would recommend this product to a friend
Doubled my water output and cut waste water in half
Great upgrade By Tom on 5/20/2013
Tom would recommend this product to a friend
I had to get a booster pump to get it to work but both were very easy to install. Made enough water over night to do a major water change in my 125 gal reef tank and fill a 16 gal ATO reservoir, Great upgrade!
Best thing for multiple tanks By Steven on 5/1/2013
Steven would recommend this product to a friend
So I must admit, I am a junky! Every time I turn around there is something new that I need. However, if you have multiple tanks then you really do need this for two reasons. 1. You do save water (being nice to our world) and 2. TIME. I hate having to wait on water before I can take care of a water change, etc. This allows for both. I never knew how valuable this was until a buddy of mine who is equally as much a junkie showed me how much faster his system was. I am a busy person and the time benefits have me sold. It is also the same construction as the existing system I have and just adding another membrane. I just wish the push connects were not as tricky when you get too many tubes in a small space.
Great ! By Mark on 4/1/2013
Mark would recommend this product to a friend
I don't know why I waited so long to upgrade my RO unit. I am so glad that I finally ordered this add on unit. By using this one upgrade, I am no longer watching water and money go down the drain. I also forgot to mention that this cuts way down on the time to make RO/DI water, and time is also something that I never have enough of. Go ahead and make the right choice. Get one and see what I mean.
Best bang for buck thing I have bought for my tank. By Justin on 4/1/2013
Justin would recommend this product to a friend
Easy to install and works as advertised, I can make 15 gallons in 2 hours. Previously it was 55-75mins for 5 gallons. Waste was about 1:3 and now its somewhere between 1:1 to 1:2
Great video instructions.
Money & Time definitly on your side! By Brandin on 3/31/2013
Brandin would recommend this product to a friend
I was previously using the BRS 75 Gal/day unit and decided to add this upgrade to save some time making water for my 225 gal, 55gal, 20gal, and 10gal tanks as well as save some money on the water bill. It was well worth it! The unit now fills my 32gal drum in a couple hrs or less. It used to take me around 3hrs just to fill my 20gal bucket. The waste water produced was dramatically reduced too. BRS even made it super easy with a great how to video and was nice enough to include all the accessories needed and more! Thanks BRS!
extremely easy to install. should come standard with future ro di kit from brs By chen yang on 3/30/2013
chen yang would recommend this product to a friend
this kit isnt all that expensive. gives better rate, save time and money, waste less water. easy to install. i suggest future brs deluxe ro di should have 150 gpd instead of 75. but remember though your psi should be higher than 60 if u want to use this otherwise it will not be efficient. i bought the booster pump from bri just to use this membrane. i want more kits from brs. this kit should combine with the booster pump kit. combine two kits and lower the price a bit thats my suggestion
Lowered my water bill a good deal By Anthony on 2/26/2013
Anthony would recommend this product to a friend
I make A ton of water for my system total system evaporates 5 gallons a day. That with my water change water was driving up my water bill. Added this to my 5 stage plus and my water output sky rocket and my waste water was cut in half also I noticed my di resin last a lot longer!!! Saves a ton of money!! Worth the small investment
If recommend! By Toby Williams on 2/22/2013
Toby Williams would recommend this product to a friend
This really cuts waste down and easy to install. Keep in mind this upgrade needs 60 psi to work efficiently. I had 67psi at the faucet, after running 1/4" supply line from spigot and up the wall through my attic and into the garage to the unit, I was only getting 51-55 psi at the membranes. It's about a 20' total run with waste line doing the same at about 25' out to the back of the house. It still works fantastic with a lot less waste, but it looks like ill be getting the booster, because my DI Resin is depleting fast at the 1st canister of the dual DI, also I think I'd get a better rejection rate and even less waste also with faster production. Bottom line. We all hate to buy things we don't need but be prepared if your doing your setup like me with similar spigot pressure.
BRS 150 GPD Water Saver Upgrade Kit well worth the money By Kenneth on 2/16/2013
Kenneth would recommend this product to a friend
I have been running a 50GPD Coralife RO/DI unit for a few years now. The system was extremely slow to produce good water and quick on producing waste water. Based off information I found on BRS and other website sites I changed my setup. I first upgraded my membrane to 75GPD and replaced the flow restrictor on my system. This improved the good to waster water ratio. The next upgrade I did was to add the BRS 150 GPD Water Saver Upgrade Kit. The video on installing this kit made the upgrade simple. The install took less than 10 minutes and was extremely simple and have not had any problems with leaks. The key to the install is making sure you can the water tubing as close to straight as possible. It's nice that you get 5 Feet of Red, White, Blue and Black RO Line with the kit. The install of the kit has increased my output and has reduced the amount of waste water I produce. I have also now added a booster pump which has helped reduce the amount of time it takes to produce water and seems to have helped with the consumption of the DI resin.
Fantastic Upgrade By Dan on 2/15/2013
Dan would recommend this product to a friend
Well I had been running a 75 gpd unit with a booster pump and was realatively happy, but I wanted to cut down on the waste water. Well I can say that it certainly does cut down on the waste water and boosts output dramatically. Prior to installation I was producing about 1 gallon of good water to 3 gallons of waste. After installation I'm producing 1 gallon of good water to 1.3 gallons of waste. I would say thats a dramatic reduction in waste water. Also I just fill my ATO bucket which holds 6 gallons of water. The unit produced 6 gallons in 59 minutes! That works out 146-147 gallons per day. The booster pump has keeps a constant 78 psi while producing. I would definetely recommend this upgrade. Thanks BRS!
Works just fine By LOUIS on 2/15/2013
LOUIS would recommend this product to a friend
I added this based off the video on improving the ratio of good to bad water produced from using a 5 stage ro/di unit. I didn’t notice the difference until I added the booster pump after I realized that I wasn’t getting the 65 or more psi. After attaching the pump I had less water to dispose of. I wasn’t just letting the refused water go down the drain, I was storeing it in two 55 gallon barrels to water the lawn and garden with.
Awesome way to increase output and save water. By Al on 1/28/2013
Al would recommend this product to a friend
I started with 1 upgrade kit, and liked the results so well that I purchased a 2nd and then a 3rd (total 4 RO's). So if anyone else wondered what would happen, let m explain. With 2 upgrade kits (total 3 RO's) and the booster pump, I was getting 3:1 rejection rate - for every 3 gallons of water in, I got 1 gallon of product water out. When I added the 3rd upgrade kit, not only did my pressure drop way down, but there was no further improvement in rejection rate.
Super easy to install, boosted my system and saved time. By Jerry on 1/23/2013
Jerry would recommend this product to a friend
Super easy to install, boosted my system and saved time. I cut my time to make RO water in less than half. Set up auto top off and makes things even easier. Good upgrade.
Now have tons of water! By Jeremy on 1/2/2013
Jeremy would recommend this product to a friend
Was a piece of cake to install via there great how to videos!
Best Upgrade to my BRS 75GPD RO/DI system By Collin on 12/23/2012
Collin would recommend this product to a friend
I originally had a 75GPD RO/DI system from BRS, but it took 3 hours to make one batch of water needed for a water change. After adding this kit, the time I needed to make RO water was cut in half. Plus, I was wasting less water, is always good.
Definitely worth the upgrade if you have an existing RO system with only 75GPD.
The video instructions make it super easy to set up as well!
LIKE A FIREHOSE!!!!!! By Anthony on 12/17/2012
Anthony would recommend this product to a friend
This paired up with the booster pump kit is like a firehose compaired to what it was before. LOVE IT!!!!
Frickin AWESOME By Tony Winsor on 12/16/2012
Tony Winsor would recommend this product to a friend
This paired up with the booster pump is the Best addition to ANY RODI unit.
Save $$$ You will cut down your water bill big time with this kit By Rob Coberg on 12/9/2012
Rob Coberg would recommend this product to a friend
I am learning as I go. I built my RO/DI system using a 75 GPD membrane and it is slow. I bought this Kit and not only did it double the output, the waste water is cut down to a low ratio. next to add is a booster pump with a auto shut off.
Works great! By Sean on 11/20/2012
Sean would recommend this product to a friend
Works great - added to my Max cap unit - along with a flush kit and appropriate flow restrictor - and wonderful things happened.
Note prior to this I had the CDP8800 booster pump dialed in at about 70-75 PSI (depending on filter lifecycle) with a single membrane since my utility water was normally 40-50 PSI which is borderline.
This installed quick and easy. Only thing I wish is that BRS had the option to order it with a pressure gauge (or at least with a plugged pressure gauge hole) to match my first membrane.
I primed everything, and also replaced my original membrane at the same time (bought her at BRS same order), ran a flush for good measure, then turned the system into production - measured waste water to product water ratio - it went from 5:1 to 2:1, and TDS rejection shot way up - post filter, I am at about 170PPM. Single membrane was throwing off 5-8 PPM product after running for awhile and settling down. Now, I am seeing 1PPM! That may not seem like much, but saves a lot of DI life, and makes for a 99.41% rejection rate! It's kept this up for 4 months now - I think flushing for a good minute at start and shutdown makes some difference too.