good By James on 3/14/2014
James would recommend this product to a friend
fast shipping, dosent leak, what more can you ask for. Thanks!!
Works Great for 200G Saltwater Mixing Station By Kyevey on 3/5/2014
Kyevey would recommend this product to a friend
I bought 4 of the 1" Uniseal.
Had no issue with the installation. Seal fit snug prior to inserting the PVC. Once the 1" PVC was added it was a perfect seal, no leaks...
I've been using with high power Iwaki pump which creates a bit of vibration with the PVC and the Uniseals absorbs the vibrations much better than any Bulkhead could!
GOOD By JWEPPEL on 2/26/2014
JWEPPEL would recommend this product to a friend
BOUGHT THE 1", BE CAREFUL WHEN CUTTING HOLES. DID IT TO ROUGHNECK GARBAGE CONTAINER FOR SALTWATER MIXING STATION,AND STARTING OUT ON 2 OF 3 HOLES DIDNT QUITE CUT A CLEAN,ROUND, NO BURR HOLE. AND SOME LEAKED. WENT BACK AND PUT SILICONE ON THEM NOW FINE.
works as should By gavin on 2/18/2014
gavin would recommend this product to a friend
i bought a the hole saw to make a water station for my tank. The seal was allittle loose but holds water good
Simple and easy By eric on 1/5/2014
eric would recommend this product to a friend
Used several of these on brute containers to build a water storage/mixing station. Work fantastic.
awsome By Denton on 12/25/2013
Denton would recommend this product to a friend
This is an excellent piece great idea all the way around easy and fast
Excellent By Scott on 11/24/2013
Scott would recommend this product to a friend
I used these on my salt mixing station. Perfect seal the first time on a rounded barrel. It does take a bit of work to get the pipe into the seal, but soapy water helps it along nicely.
Works, though some issues on very curved surfaces. By PuffDaddy on 10/15/2013
PuffDaddy would recommend this product to a friend
These work well. Except when the surface is too curved in relation to the bar you are inserting. I attempted to put 1" PVC into a 3" PVC section. I was not able to insert the pipe. The 1/2" into the 3" worked like a charm though. I feel like these are intended for joining PVC to less curved surfaces. make sure your ratio of main diameter to insert diameter is above 4:1.
these rock too By the hack on 9/29/2013
the hack would recommend this product to a friend
Perfect product By Grover on 9/29/2013
Grover would recommend this product to a friend
I used this product on a Bee hive feeder.
I drilled a hole through the side of a Bee Hive Installed the 3/4" uni-seal then cut ~2" long 3/4" schedule 40 pvc pipe glued on 3/4" elbow and inserted into the side of the hive and added clear tubing so the feeder can be refreshed without opening the hive.
great for the price!! By solarmoonman on 6/27/2013
solarmoonman would recommend this product to a friend
These work great.... but depending on the wall thickness of the unit your using can be VERY VERY hard to get pipe in..I used them on a 55 gallon food grade plastic drum....worked like a charm... no leaks and was fairly easy to get pipe in...Then I also used them on a 100 gallon rubbermaid stock tank... still once I was done... NO leaks... but I had to file out one of the holes a little bigger as the wall thickness was to big a the bottom and I just could not get the pipe in...
Tip make sure the pipe has been cut off square..(90 degrees). like with a chop saw...then use some 80 grit sand paper to round off the edge of the pipe to remove the knife like edge ... or it will cut/ dig in to the rubber.
all in all for the price there great...a bit of a challenge to install on thicker walled units but i used 8 two inch and 8 1 1/2 " on my new system.... not a drop!!!!!
they r very helfpul little things By Awais on 4/18/2013
Awais would recommend this product to a friend
These unseals are very helpful, esp for the small sizes, where you may not want to use a bulkhead, use these uniseals. They are great, I used them in my refuge when I drilled holes in them. I also used them in my DIY BP reactors.
They are easy to use and they do not leak, just make sure you drill the right size holes.