- Home /
- PhosBan Reactor 150
Starting at: $59.99
Starting at: $1.39
I wouldn't recommend this product By Nikolas on 9/28/13Nikolas wouldn't recommend this product to a friendI did try to use this product for carbon and ferrous oxide as well as for biopelets Designed is flawed due to the fact that PhosBan uses a small mesh at the bottom of the device and on top in little period of time mesh become clogged and whole set up become useless I should say that mesh provided for biopelets use however for carbon and ferrous oxide the perforated plates at the bottom and top clogged quickly as well and make media stopped tumbling.Plus add some very inconvenient design of internal fittings which tend to disconnect or slip off and hard to set up in general plus that upper screw in cover that need to be watch out because it could leak any time The product poorly designed I garbaged it all and replace Yes with more expensive Reef Octopus product which is dream to use well designed I wish I didn't try to cheap and waste money on those PhosBan and go strait to buy ReefOctopus Don't make my mistake You get what you pay
Cheap By Moe on 9/6/13Moe wouldn't recommend this product to a friendI have this reactor for last 9 months. I have been fighting with GHA and it has is still an issue. The product is a cheap and is not meant to last. I am planning to upgrade to BRS dual reactor. I have read some good reviews about that. If u're planning to buy it, think twice. I have been using it with RowaPhos instead of phosban because it's much more premium quality GFO than phosban. If you happen to break the plastic rings while cleaning the product is dead. Sponge rings are not that great and wear out in months. sponges can be bought seperately but the shipping is expensive on these things. Over all prodcut is cheaply made and you don't get the bang for your buck.
just the right size By Dutch on 8/19/13Dutch would recommend this product to a friendCurrent setup is a 75 gallon display and 40 gallon sump. Fits nicely into an already jam-packed sump. Easy assembly and holds more than enough GFO. Valve makes for easy flow adjustments. This reactor piggy backs off of another reactor currently housing carbon and Purigen. Don't overtighten the top otherwise it will be hard to get off.
Great product! By Fu on 4/20/13Fu would recommend this product to a friendEasy to install, does what it is supposed to and works great! For the price you can't beat this. The only negative is the difficulty in removing the cap.
Great Product By Seth on 3/30/13Seth would recommend this product to a friendThis has been my favorite phosban reactor. It holds a ton of media. I have this running on my 150 gallon with no issues. I am sure this would be just perfect for a 180 gallon as well. This unit does a great job not letting any media fall into the tank. Easy to set up, runs great!
Use a rubber glove to remove lid. By Mike on 3/27/13Mike would recommend this product to a friendI've recently purchased this reactor and I'm happy with it so far. I also found the lid difficult to remove but mainly because I couldn't get a good enough grip. I put on a rubber glove and that made removing the lid very easy!
I'm not very confident in the rubber angles but even if they go bad it will be easy to use standard clear tubing.
good price and works By Kirk on 1/31/13Kirk would recommend this product to a friendThis is the only reactor that I have had so I can not say that this is the worst one or the best but I can say it does get the job done, I like that it is small, work in or out of the sump, and easy to use. There is some bad though, hard to get off lid and plumbing isn't the greatest.
Cheap By Edward on 12/8/12Edward wouldn't recommend this product to a friendI have owned this reactor for 6 months now. It does do the job however I am replacing this with the BRS reactor soon. The rubber Elbows on the lid have cracks all over them now and I am concerned one day they will leak, when i am not home and cause a big mess. and i also like to add removing the lid to change out media is a real pain. I never tighten it down that tight but when you go to remove it. It is always stuck. I Usually have to bring the reactor to my vice to get the lid to budge.
Awesome Product By william on 11/28/12william would recommend this product to a friendHave been using a couple of these reactors for GFO and Carbon. Setup is extremely simple, and product works great. Wish it came with tubing, but that's my only complaint. Love the included ball valve.
Simple and Efficient Reactor By Chris on 10/13/12Chris would recommend this product to a friendComes with pretty much everything needed to install. Just need a pump and tubes. Can be installed in a couple different configurations in just a matter of minutes.
Does the job at better price By Mark on 9/5/12Mark would recommend this product to a friendBought this Phosban reactor about a month ago. Decent quality build. It comes with an array of tubing, tubing extensions and accessories such as a valve for adjusting flow. The instructions were clear and easy to understand. This reactor is easy to load with media and within a few days of hooking it up my phosphates dropped from around 1.14 to 0.4. Overall its a great product for the price. I definitely would recommend this.
Good price By Jonathan on 8/23/12Jonathan wouldn't recommend this product to a friendWhile I cannot argue with the fact that this product got the job done. It did make things a little bit difficult. I found that after using it for a couple weeks it was often times extremely difficult to get the lid off and I found myself having to use a pipe strap. For the price this is a good product but I moved on to a more expensive reactor for easier dissasembly.
Ask a Question About 'PhosBan Reactor 150'
Previously Asked Questions
No questions have been asked yet.
The PhosBan Reactor 150 is designed to push water upwards from the bottom and through the media. This forces an even distribution of water throughout the media and prevents channeling from occurring. The PhosBan 150 can be mounted under the aquarium or hung on the back of the aquarium. It comes with barb hose fittings for 1/2" tubing and a 1/2" barbed ball valve included for flow control. The Phosban 150 is compatible with with any pump with a flow rate between 100 and 250gph and 1/2" connections. Tubing sold separately.
Deal of the Day!
BRS 5 Stage PLUS RO/DI System - 75GPDEnds in
Regular Price: $199.99
Special Price: $179.9900:00:00:00
- Bulk Media & Additives
- Bulk Reverse Osmosis Filters & Systems
- Bulk Dry Live Rock & Live Sand
- BRS Additives
- Red Sea Additives
- Korallen-Zucht Additives
- Two Little Fishies
- Fauna Marin Aquarium Additives
- Auto Top Off Systems
- Filter Media
- Fish & Coral Foods
- Fragging Supplies
- Heaters & Chillers
- Medications & Pest Removal
- Monitors & Controllers
- Protein Skimmers
- Sumps, Tanks & Refugiums
- Tank Maintenance & Salt Mix
- UV & Ozone
- Videos & Books
- New Products
Send us your feedback
Let us know.
Hours: 9am - 5pm CST M – F
6325 Sandburg Road, Suite 400
Golden Valley, MN 55427 Map
View Larger Map 6325 Sandburg Road, Suite 400, Golden Valley, MN 55427