- Home /
- Glycerin Filled Pressure Gauge 1-100 PSI
Product performed as expected! By Phil on 10/22/2014Phil would recommend this product to a friendI suspected my water pressure was low when after only about 60 gallons I burned through nearly 1/3rd of my DI resin. I purchased a BRS pressure gauge (SKU: 200215) and discovered that the pressure coming from under my sink where I connected my RODI system inline was around 45PSI. As we all know I need >60PSI for my 150GPD Upgraded RODI system to operate optimally. I purchased the booster pump (SKU: 207951) and it did exactly what it was supposed to do! I set it up inline between my water source and my RODI unit, plugged in the power supply (SKU: 200201) and my water pressure went up from 44 to ~95. Not only did I see an increase in RODI production to the 175GPD (as expected), but I'm using less than HALF the DI resin I was before.
Pressure Gauge to Upgrade my RO/DI By Mark on 9/29/2014Mark would recommend this product to a friendI chose this glycerin filled gauge because I believed it would be a step up from the air filled gauge. I must say that it has not disappointed. It was a very easy push in installation. I used this gauge initially to check to pressure from my tap and then to continuously check the pressure going to the membrane. It gives me a good indication on when to change my carbon and pre-membrane filters.
works great By Mario on 6/9/2014Mario would recommend this product to a friendHave this placed after my booster pump. Made adjusting water pressure a breeze. Going 2 get another one so when I see my pressure drop I know that my filters need to bechanged
Important part of my upgrade By Manfred on 2/18/2014Manfred would recommend this product to a friendI bought this gauge to help monitor the pressure I was getting with my system and to determine when I needed to change filters. Takes a lot of the guess work out of the process. The less left to chance the better off you are.
liquid filled pressure guage By nicholas on 2/9/2014nicholas would recommend this product to a friendthis is a must have if you are running a booster pump on your rodi unit. the air filled make noise due to the pressure making it bounce off the limiter. lots easier to read and more accurate.
quality equipment By Alabama Reef on 1/27/2014Alabama Reef would recommend this product to a friendeasy to install in my RO unit. Put between my booster pump and RO membrane. Pretty heavy gauge.
To soon to tell By none on 1/27/2014none wouldn't recommend this product to a friendthis was to replace one that failed after a short time, I have not replaced it yet. The last gauge <non glycerine> I had was in use well over 15 years before it failed. We'll see?
Replacement Gauge By Adam on 1/8/2014Adam would recommend this product to a friendI purchased this to replace the air filled gauge that went bad on my RODI. This is a much nicer gauge and it seems like it will not fail like the air filled one. Only time will tell
Reliable By Sven on 11/7/2013Sven would recommend this product to a friendI put two of these in line with each other and they are both spot on. Also, you never have to tap these glycerin filled gauges to get the needle unstuck!
Works Great By Cameron on 10/5/2013Cameron would recommend this product to a friendInstalled yesterday so far so good. If installing yourself you need a 9/16" metal bit to drill the hole in the bracket if you want to install it like it is on the Plus systems. Also get a Y adapter and 90 degree elbow fitting if you want to run the hoses like the Plus systems
Works great By Trojan on 9/21/2013Trojan would recommend this product to a friendIt has not let me down yet.
Great add on By Tim on 12/28/2012Tim would recommend this product to a friendTook 20 seconds to install. Was happy to see it reading 50psi. Now I don't have to guess when to change the filters. Well worth the money.
Pressure gauges, flush kits and TDS meters are eas ...
Sufficient PSI is very important for the correct operation of a reverse osmosis unit. Low water pressure is a leading cause of poor RO system performance. A pressure gauge assures that proper pressure is being supplied. It will also make pressure drops apparent which can tell you that sediment and carbon blocks need to be changed.
Glycerin filled pressure gauges absorb vibration and pressure spikes increasing service life. This glycerin filled pressure gauge comes assembled with 1/4" quick connect fittings for quick easy installation in-line before the RO Membrane. This item is designed for use with our saltwater aquarium line of RO systems.
- Bulk Media & Additives
- Bulk Reverse Osmosis Filters & Systems
- Bulk Dry Live Rock & Live Sand
- Auto Top Off Systems
- Calcium, Alkalinity & Trace Elements
- Controllers, Monitors & Testing
- Filter Media
- Fish & Coral Foods
- Fragging Supplies
- Heaters & Chillers
- Pumps & Plumbing
- Salt Mix & Tank Maintenance
Skimmers & Reactors
- Internal Protein Skimmers
- External Protein Skimmers
- Hang On Skimmers
- Ozone Equipment
- Nano Skimmers & Accessories
- UV Sterilizers
- Sumps, Tanks & Refugiums
- Specials, New & BRS Gear
Send us your feedback
Let us know.
Phone Hours: 7am - 7pm CST M-Th
10am-4pm CST Friday
6325 Sandburg Road, Suite 400
Golden Valley, MN 55427 Map
View Larger Map 6325 Sandburg Road, Suite 400, Golden Valley, MN 55427