- Home /
- Air Filled Pressure Gauge 1-100 PSI
Don't bump them By Paul on 10/22/2014Paul would recommend this product to a friendBe very careful with these. If you bump them they will jump up or down in the current reading and stay there. both of mine came stuck at 20, so BRS sent me 2 new ones. The previous ones still work, I just have to subtract 20. Put one before and after your filters so you know when to replace them due to clogging. Simple install. It also gives you a good idea of water pressure so you know if you need to buy a pump or not.
A Must Have By Dave on 9/5/2014Dave would recommend this product to a friendIf you are running RO/DI you need to know what your pressure going into the unit is, so as to optimize your units performance. This gives you that information. Wish I had it from the beginning. I only knew that I had decent pressure, but then again I was guessing as I was wrong. No I know and it's working better than ever.
You need this! By William on 7/26/2014William would recommend this product to a friendI wasn't getting the best production out of my RO/DI unit. I replace the filters and still not great. I purchased this inexpensive product and found that i didn't have great pressure. This works great and save you money.
air filled pressure guage By nicholas on 2/9/2014nicholas would recommend this product to a friendworks for knowing the pressure going to your RODI unit. But go with the liquid filled if you are running it right after a booster pump. if it is anywhere else in the line you are good.
Simple and affordable By Michelle YV, CA on 12/15/2013Michelle YV, CA would recommend this product to a friendNice little pressure gauge, It's affordable and easy to install
SIMPLE AND AFFORDBLE By jason on 11/27/2013jason would recommend this product to a friendVERY EASY TO INSTALL AND GIVES YOU A ACCURATE PRESSURE READING. I HAD NO CLUE MY WATER PRESSURE WAS ACTUALLY AS GOOD AS IT WAS. I WAS GOING TO BUY A BOOSTER PUMP HAD I NOT GOT THIS DEVICE AND BOY WOULD I HAVE FELT DUMB....
Works perfect By Bill on 9/26/2013Bill would recommend this product to a friendEasy to integrate with my RO/DI system. Works as expected.
Good buy By Chris on 8/2/2013Chris would recommend this product to a friendIt's very easy to install and works great. I ordered it from Canada and it was painless. Ordered it on a Thursday and received it on the following Thursday. Very happy with the service.
It is what it is By David on 7/17/2013David would recommend this product to a friendDo you need to know your pressure. Bam! this does that. Easy to read and set up.
Works great! By Matt on 5/16/2013Matt would recommend this product to a friendThis one was to replace my stock one on my BRS system. Works perfectly, although with the booster pump it does shake the needle back and forth some within 5 psi due to the pressure load.
Must have for any rodi unit By Anthony on 4/12/2013Anthony would recommend this product to a friendNot only is is easy to install but is beneficial for proper use of your unit to determine if new filters are needed by pressure dropping lower than average
Wonderful By Timothy on 9/10/2012Timothy would recommend this product to a friendNo complaints. Get's the job done and let's me know what the pressure is going to my BRS RODI unit.
Pressure gauges, flush kits and TDS meters are eas ...
Previously Asked Questions
by Michelle on December 6, 2013, @6:43 PM
Just got the air filled pressure gauge for my 75 gpd economy rodi unit. I'm not sure where to place it???
Can you help? I'm thinking it should be connected on top of the unit where the red line comes out of the DI cartridge maybe?
Bulk Reef Supply Hi Michelle,
The pressure gauge goes on the line between the last carbon block and the membrane (Which is a red line). Simply cut the tube and insert the pressure gauge tee.
Sufficient PSI is very important for the correct operation of a reverse osmosis unit. Low water pressure is a leading cause of poor RO system performance. A pressure gauge assures that proper pressure is being supplied. It will also make pressure drops apparent which can tell you that sediment and carbon blocks need to be changed.
This air filled pressure gauge comes assembled with 1/4" quick connect fittings for quick easy installation in-line before the RO membrane. This product is designed for use with our saltwater aquarium line of RO systems.
Deal of the Day!
BRS Extra Thick Gel Super GlueEnds in00:00:00:00
Deal of the Day!
Red Schedule 40 Pipe (5 ft)Ends in00:00:00:00
Deal of the Day!
Blue Schedule 40 Pipe (5 ft)Ends in00:00:00:00
- Black Friday Doorbusters
- Bulk Media & Additives
- Bulk Reverse Osmosis Filters & Systems
- Bulk Dry Live Rock & Live Sand
- Auto Top Off Systems
- Calcium, Alkalinity & Trace Elements
- Controllers, Monitors & Testing
- Filter Media
- Fish & Coral Foods
- Fragging Supplies
- Heaters & Chillers
- Pumps & Plumbing
- Salt Mix & Tank Maintenance
Skimmers & Reactors
- Internal Protein Skimmers
- External Protein Skimmers
- Hang On Skimmers
- Ozone Equipment
- Nano Skimmers & Accessories
- UV Sterilizers
- Sumps, Tanks & Refugiums
- Specials, New & BRS Gear
Send us your feedback
Let us know.
Phone Hours: 7am - 7pm CST M-F
6325 Sandburg Road, Suite 400
Golden Valley, MN 55427 Map
View Larger Map 6325 Sandburg Road, Suite 400, Golden Valley, MN 55427